80-Amp E-flite Pro Brushless ESC with Switch-Mode BEC

• Up to 80 amps continuous current with proper air flow and 100 amps burst current (15 seconds)
• 5V switch-mode BEC capable of 5 amps continuous current with 6 amps max burst on any recommended input voltage
• Drive up to 7 analog or 6 digital standard-size servos with the BEC on any recommended input voltage
• 3- to 6-cell Li-Po, 9- to 18-cell Ni-MH/Ni-Cd input voltage
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable low voltage cutoff with settings for 3-cell Li-Po (9.2V), 4-cell Li-Po (12V), 5-cell Li-Po (15V), 6-cell Li-Po (18V) or 74% of battery starting voltage
• Programmable throttle input range (1.1ms–1.9ms or 1.2ms–1.8ms)
• Programmable soft start-up rate - .25 second or 1 second
• Auto motor shut down if signal is lost or there is interference
• Programmable timing—5 user-selectable ranges–use with a large variety of brushless motors
• Two operating modes–Airplane or Heli
• Pre-wired connectors—E-flite EC5 on battery input and 4.0mm female gold bullets on motor output leads

When performance matters in your high-current applications, look no further than the E-flite® 80-amp Pro switch-mode ESC. This is a high-quality, efficient sensorless brushless electronic speed control with an integrated switch-mode BEC. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication. It is capable of up to 80 amps continuous current when using 3- to 6-series Li-Po battery packs. You can drive up to 7 analog or 6 digital standard-size servos with the BEC on any recommended input voltage. Featuring an exposed, finned heat sink aluminum case with lightweight plastic end-caps, safe power-arming along with advanced programmable features such as low voltage cutoff, braking, timing, throttle input range and more, the E-flite 80-amp Pro switch-mode ESC is truly a ‘pro series’ electronic speed control.

Specifications:

• Amperage: 60 & Up
• Auto Cutoff: Yes
• BEC Continuous Current: 5A
• BEC Voltage: 5.5V Switch-mode
• Brake: Yes
• Cells w/BEC: 9-18 cells NiMH, 3-6S LiPo
• Continuous Maximum Current: 75 - 100A
• Forward: Yes
• Height: 0.62 in (15.5mm)
• Input Connector Types: EC5, 10AWG leads
• Length: 3.0 in (77mm)
• Momentary Peak Current: 100A (15 seconds) Proper Cooling Required
• Output Connector Types: 4mm Gold Bullet, 12AWG leads
• Overload Protection: Yes
• Time Delay Brake: Yes
• Type: Brushless
• Weight: 3.75 oz (106 g)
• Width: 1.6 in (41mm)

• Amperage: 60 & Up
• Auto Cutoff: Yes
• BEC Continous Current: 5A
• BEC Voltage: 5.5V Switch-mode
• Brake: Yes
• Cells w/BEC: 9-18 cells NiMH, 3-6S LiPo
• Continuous Maximum Current: 75 - 100A
• Forward: Yes
• Height: 0.62 in (15.5mm)
• Input Connector Types: EC5, 10AWG leads
• Length: 3.0 in (77mm)
• Momentary Peak Current: 100A (15 seconds) Proper Cooling Required
• Output Connector Types: 4mm Gold Bullet, 12AWG leads
• Overload Protection: Yes
• Time Delay Brake: Yes
• Type: Brushless
• Weight: 3.75 oz (106 g)
• Width: 1.6 in (41mm)